Home > Could Not > Could Not Detach Kernel Driver Interface

Could Not Detach Kernel Driver Interface

Contents

Looks like I have a slightly different version of the sensor (just arrived from amazon) but it's the same VID/PID. DUB-H7 7-port USB 2.0 hub (older grey/silver version) Hubs that are known to not work: rosewill 7-port USB hub (TERMINUS TECHNOLOGY INC.) satechi 12-port USB hub (TERMINUS TECHNOLOGY INC.) cerulian 7-port If you want to test the update, you can install it with su -c 'yum --enablerepo=updates-testing update nut'. After sudo su'ing cat /etc/nut/ups.conf: [eaton] driver = usbhid-ups port = auto desc = "Eaton 3S" upsdrvctl -t start Network UPS Tools - UPS driver controller 2.6.1 *** Testing mode: not http://asmwsoft.net/could-not/could-not-attach-to-driver-is-kernel-module-loaded-mac.html

Owner padelt commented May 19, 2014 I cannot see the behavior with my two tempers over ~24h. Posting to weewx user How to convert from setup.py install to debian install i2C sensor and other python scripts logging logwatch maxbotix Minimize writes on SD cards mqtt multi threaded service Installing the software is easy, just use the magic words: sudo apt-get install nut nut-cgi To configure nut on Ubuntu I start by reading this guide by a mysterious person named If someone has an idea how to approach that let me know please. http://askubuntu.com/questions/113994/trouble-starting-network-ups-tools-with-a-eaton-3s-ups

Can't Claim Usb Device

What does it look like? The final result is that the driver doesn't start, and connection failure to the driver / UPS are reported by upsd and upsmon. This seems to have been breaking the USB connection after a small number of polls. Bus 001 Device 012: ID 03f0:c602 Hewlett-Packard Photosmart D7100 series Bus 001 Device 011: ID 0c45:6242 Microdia PC Camera (SN9C201 + MI1310) Bus 001 Device 009: ID 04cc:1521 Philips Semiconductors USB

Then again I have that one suspicion that the interaction happening in https://github.com/padelt/temper-python/blob/master/temper/temper.py#L112 is at fault or at least making it worse. What to do when you notice that a value in your paper is wrong, once it is accepted but before it is published? Use wee_device to change the station's archive interval to match whatever you specify in weewx.conf. Nut Ups From the NUT FAQ : "My USB UPS is supported but doesn’t work!" : On Linux, udev rules are provided to set the correct permissions on device file.

We'll assume you're ok with this, but you can opt-out if you wish.Accept Read More Adi Roiban Who wipes ? nut-2.4.3/drivers $ sudo ./usbhid-ups -a CP550SLG -D -D Network UPS Tools - Generic HID driver 0.34 (2.4.3) USB communication driver 0.31 0.000000 debug level is '2' 0.000408 upsdrv_initups... 0.000583 Checking device Maybe because its just cheap hardware, maybe because its polled to often. https://bugzilla.redhat.com/show_bug.cgi?id=488368 USB 2.0 Hub) Beware of random factory resets Some consoles randomly reset some or all of their settings to factory defaults.

Since the lockup happens in the station firmware, no weather station software is immune. You can provide feedback for this update here: http://admin.fedoraproject.org/updates/F10/FEDORA-2009-5921 Comment 18 Fedora Update System 2009-06-24 15:24:49 EDT nut-2.4.1-6.fc11 has been pushed to the Fedora 11 stable repository. When the lockup happens, you will see a gap in weather data. I an unclear on this part.

Nut Error Driver Not Connected

This seems to have been breaking the USB connection after a small number of polls. We recommend upgrading to the latest Safari, Google Chrome, or Firefox. Can't Claim Usb Device With weewx 2.6.x and earlier, using polling_mode = ADAPTIVE or record_generation = hardware will increase the chance of a lockup. No Matching Hid Ups Found There was a mistake in the naming of the NUT udev rules file which resulted in the rules being overridden by another udev configuration file.

Some people experience the lockup with certain computers but not others, some report fewer lockups after switching to a powered hub or to a different USB cable. check over here This allows the NUT driver to communicate with the UPS, through this device file. Should I mention that to the editor? detaching kernel driver from USB device... Nut-cgi

How to bring attention to computational complexity? Enabling module cgid. Following the information from here: Musings of the Nannerpuss: NUT - Network UPS Tools - on Ubuntu . "... his comment is here It would appear to be a problem with stations manufactured after 2010 or so; older stations seem to be immune.

Nothing unusual here I don't think. I changed the permission to 666 for /dev/bus/usb/BID/DID (replace BID with your USB bus ID, and DID with device ID). To automatically set the permission for future connections I added the following udev rule: #/etc/udev/rules.d/10-must-pa-1060.rules SYSFS{idVendor}=='0665', SYSFS{idProduct}=='5161', MODE='0666' Then I started the UPS driver via: $ sudo upsdrvctl start If you

failed to claim USB device, trying 1 more time(s)...

more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed Test the UPS with a normal PC connected to the USB. Then the interesting question is, should this be fixed in the temper script? Why does Mike call Jimmy "Saul"?

So I went for blazer_usb. It might coincide with a change in radio communication protocols between console and sensors. detaching kernel driver from USB device... weblink Comment 5 Michal Hlavinka 2009-03-18 10:08:38 EDT Your config files looks ok.

Use a tool such as usb_control.py to see whether a hub actually works. The watchdog period is about 5-10 minutes which gives the system time to boot up. When I start usbhid-ups on its own, without "-u root", /var/log/messages doesn't contain anything (and just a "Connection refused" message when I try to start NUT via the initscript), and I Attempt to start ups service Actual results: [root@detritus ~]# service ups start Starting UPS driver controller: [FAILED] Starting upsd: [ OK ] Starting UPS monitor (master): [ OK ] Expected results:

But old stable distros could be affected.